Dimmer

The EVIC display is provided with a light sensor capable of detecting environmental light conditions and adjusting the brightness of the instruments accordingly.

NOTE: The brightness of the instrument panel may change while travelling following an event that causes switching from “day” to “night” conditions (or vice versa) in the passenger compartment (e.g. in a tunnel, on avenues in shadows, under bridges, etc.).

To adjust the brightness, proceed as follows: 1. Press the + or – button to set the required brightness level.
2. Briefly press the MENU ESC button to go back to the menu screen or press and hold the MENU ESC (approximately one second) to go back to the main screen without storing settings.

Speed Beep (Speed Limit)

With this function it is possible to set the car speed limit (mph or km/h); when this limit is exceeded the driver is immediately alerted.

To set the speed limit, proceed as follows: 1. Briefly press the MENU ESC button. The display will show the message (Speed Beep).
2. Press the + or – button to select speed limit activation (On) or deactivation (Off).
3. When the function is activated (On), briefly press the MENU ESC button to display the presently set activation speed. Pressing the + or – buttons selects the speed limit.

Press MENU ESC to confirm selection.

NOTE: Selection is possible between 20 and 125 mph or km/h, depending on the selected unit. The setting will increase/decrease by five units each time the +/– button is pressed. Press and hold the +/– button to increase/ decrease the setting rapidly. Save the setting by briefly pressing the button when you approach the required setting.

• Briefly press the MENU ESC button to go back to the menu screen, or press and hold the MENU ESC button (approximately one second) to go back to the main screen without storing the settings.

To cancel the setting, proceed as follows: 1. Briefly press the MENU ESC button. “On” will flash on the display.
2. Press the – button. “Off” will flash on the display.
3. Briefly press the MENU ESC button to go back to the menu screen, or press and hold the MENU ESC button (approximately one second) to go back to the main screen without storing the settings.

Trip B Data (Trip B On)

Through this option, it is possible to activate (On) or deactivate (Off) the Trip B (partial trip) display.

For further information see “Trip Computer.” For activation / deactivation, proceed as follows: 1. Briefly press the MENU ESC button. “On” or “Off” will flash on the display (according to previous setting).
2. Press the + or – button to select the setting.
3. Briefly press the MENU ESC button to go back to the menu screen, or press and hold the MENU ESC button (approximately one second) to go back to the main screen without storing the settings.

Set Time (Clock)

This function may be used to set the clock through two sub-menu items: “Time” and “Mode.” Proceed as follows: 1. Briefly press the MENU ESC button. The display will show the two sub-menu items “Time” and “Mode.”
2. Press the + or – button to navigate the two sub-menu items.
3. Select the required option and then press the MENU ESC button.
4. When accessing the “Time” sub-menu item, briefly press the MENU ESC button and “hours” will flash on the display.
5. Press the + or – button for setting.
6. Briefly press the MENU ESC button and “minutes” will flash on the display.
7. Press the + or – button for setting.

NOTE:
• The setting will increase or decrease by one unit each time the + or – button is pressed. Press and hold the button to increase/decrease the setting rapidly. Save the setting by briefly pressing the button when you approach the required setting.
• Briefly press the MENU ESC button to return to the “Time” sub-function.
• When accessing the “Mode” submenu, briefly press the MENU ESC button. The previously set display format will flash on the display.
• Press the + or – button to select “24h” or “12h.”

When you have selected the required settings, briefly press the MENU ESC button to go back to the Time, Mode sub-menu screen, or press and hold the MENU ESC button (approximately one second) to go back to the main screen without storing the settings.

Set Date

This function may be used to set the date (day - month - year).

To change the date proceed as follows: 1. Briefly press the MENU ESC button and “year” will flash on the display.
2. Press the + or – button for setting.
3. Briefly press the MENU ESC button and “month” will flash on the display.
4. Press the + or – button for setting.
5. Briefly press the MENU ESC button and “day” will flash on the display.
6. Press the + or – button for setting.

NOTE: The setting will increase or decrease by one unit each time the + or – button is pressed. Press and hold the + or – button to increase/decrease the setting rapidly.

Save the setting by briefly pressing the button when you approach the required setting.

• Briefly press the MENU ESC button to go back to the menu screen, or press and hold the MENU ESC button (approximately one second) to go back to the main screen without storing the settings.

See Radio (Repeat Audio Information)

With this function active, the EVIC display shows information relevant to the sound system.

• Radio: tuned radio station frequency, automatic tuning activation or AutoSTore.
• CD audio, CD MP3: track number.

To activate (On) or to deactivate (Off) the sound system info displaying proceed as follows: 1. Briefly press the MENU ESC button “On” or “Off” will flash on the display (according to the previous setting).
2. Press the + or – button for setting.
3. Briefly press the MENU ESC button to go back to the menu screen, or press and hold the MENU ESC button (approximately one second) to go back to the main screen without storing the settings.

If the radio has BLUE&ME™, refer to the appropriate “BLUE&ME™ User’s Manual” for further information.

Speed Dis

When this function is activated the cluster will display the vehicle speed (MPH or km/h).

To activate (On) or to deactivate (Off) the speed display feature, proceed as follows: 1. Briefly press the MENU ESC button. “MPH”, “km/ h”, then “Off” will flash on the display (according to previous setting).
2. Press the + or – button to select display deactivation “Off”, “MPH” or “km/h”.
3. Briefly press the MENU ESC button to go back to the menu screen, or press and hold the MENU ESC button (approximately one second) to go back to the main screen.

Autoclose

With this function active, the doors will automatically lock at when the vehicle’s speed exceeds 15 mph (24 km/h).

To change the setting proceed as follows: 1. Briefly press the MENU ESC button “On” or “Off” will flash on the display (according to the previous setting).
2. Press the + or – button for setting.
3. Briefly press the MENU ESC button to go back to the menu screen, or press and hold the MENU ESC button (approximately one second) to go back to the main screen without storing the settings.

Units (Set Units)

This function may be used to set the measurement unit in three submenus: “Distance,” “Temperature” and “Fuel Economy.” To set the required unit, proceed as follows: 1. Briefly press the MENU ESC button to display the three sub-menus.
2. Press the + or – button to navigate the three submenus.
3. Select the required sub-menu and then briefly press the MENU ESC button.
4. When accessing the “Distance” submenu: briefly press the MENU ESC button. Either “mi” or “km” will appear on the display (according to the previous setting).
5. Press the + or – button for setting.
6. Briefly press the MENU ESC button to return to the sub-menu.
7. When accessing the “Fuel Economy” submenu, briefly press the MENU ESC button. Either “mpg,” “km/l ” or “l/100km” will appear on the display (according to the previous setting).

If the distance unit set is “mi,” the fuel economy unit will be displayed in “mpg.” If the distance unit set is “km,” the fuel economy unit will be displayed in either km/l or l/100km.

1. Press the + or – button for setting.
2. Briefly press the MENU ESC button to return to the sub-menu.
3. When accessing the “Temperature” submenu: briefly press the MENU ESC button. Either “°F” or “°C” will appear on the display (according to the previous setting).
4. Press the + or – button for setting.
5. Briefly press the MENU ESC button to return to the sub-menu.

When you have made the required settings, briefly press the MENU ESC button to go back to the sub-menu screen, or press and hold the MENU ESC button (approximately one second) to go back to the main screen without storing the settings.

Language (Selecting The Language)

The messages can be displayed in the following languages: Italian, English, German, Portuguese, Spanish, French, Dutch, Polish.

To set the required language, proceed as follows: 1. Briefly press the MENU ESC button. The previously set “language” will flash on the display.
2. Press the + or – button for setting.
3. Briefly press the MENU ESC button to go back to the menu screen, or press and hold the MENU ESC button (approximately one second) to go back to the main screen without storing the settings.

Buzzer Volume (Adjusting The Failure/Warning Buzzer Volume)

With this function the volume of the buzzer accompanying any failure/warning indication can be adjusted to one of eight volume levels.

To adjust the volume proceed as follows: 1. Briefly press the MENU ESC button. The previously set volume “level” will flash on the display.
2. Press the + or – button for setting.
3. Briefly press the MENU ESC button to go back to the menu screen, or press and hold the MENU ESC button (approximately one second) to go back to the main screen without storing the settings.

Button Volume (Button Volume Adjustment)

This function may be used to adjust the volume of the beep accompanying the buttons. MENU ESC , + or – can be adjusted according to 8 levels.

To adjust the volume, proceed as follows: 1. Briefly press the MENU ESC button. The previously set volume “level” will flash on the display.
2. Press the + or – button for setting.
3. Briefly press the MENU ESC button to go back to the menu screen, or press and hold the MENU ESC button (approximately one second) to go back to the main screen without storing the settings.

Belt Buzzer (Buzzer Activation For S.B.R.

Indication)

This function will only be displayed after a FIAT Group Automobiles Dealership has deactivated the S.B.R.

system.

Daytime Running Lamps (DRL)

This function may be used to activate / deactivate the Daytime Running Lamps.

Proceed as follows to switch this function on or off: 1. Briefly press the MENU ESC button to display the three sub-menus.
2. Briefly press the MENU ESC button. “On” or “Off” will flash on the display (according to previous setting).
3. Press the + or – button for setting.
4. Briefly press the MENU ESC button to go back to the menu screen, or press and hold the button (approximately one second) to go back to the main screen without storing the settings.

Hill Start Assist

This function is used when starting a vehicle from a stop on a hill. Hill Start Assist maintains the same level of brake pressure the driver applied for a short period of time after the foot has been removed from the brake pedal.

Proceed as follows to switch this function on or off: 1. Briefly press the MENU ESC button. “On” or “Off” will flash on the display (according to previous setting).
2. Press the + or – button for setting.
3. Briefly press the MENU ESC button to go back to the menu screen, or press and hold the button (approximately one second) to go back to the main screen without storing the settings.

Exit Menu

This function closes the initial menu screen.

Briefly press the MENU ESC button to go back to the main screen.

Press the – button to return to the first menu option (Speed Beep).

Press the + button to return to the last menu option (Daylights).